Skip to content
SPSDPSPlanning & Building Tools

Thermal insulation materials

Lower thermal conductivity (k) means better insulation per thickness. Values below are approximate and derived from published R-values; always use the product data sheet for design.

Cost tiers are RELATIVE only (lower / medium / higher). SPSDPS does not publish current prices - get written local quotations.

The short answer

Insulation helps most on the roof and sun-facing walls. Fire safety and moisture detailing matter.

If your situation is this, choose that
If you need...ConsiderWhy
Terrace roof heat reductionXPS or PU/PIR boards above slabBoard insulation over the slab keeps the heat out.
Tight budget wall or roof panelEPSLower cost; check density and fire behaviour.
Sound and heat between roomsGlass wool or rock woolFibrous mats also help acoustics; keep them dry.
Fire-critical areaRock wool (ask for the fire rating)Mineral wool resists fire better than foam types.

All options at a glance

All options at a glance
OptionRelative costBest forWatch out for
EPS (expanded polystyrene)LowerRoof and wall insulation with fire-safe detailing.Combustible
XPS (extruded polystyrene)MediumInverted roofs and damp-prone areas.Combustible
PU / PIR foamHigherWhere thickness is limited.Highest cost
Glass woolMediumFalse ceilings, partitions and acoustic walls.Loses performance when wet
Rock / mineral woolMedium to higherFire-rated walls and ceilings.Heavier

Compare side by side

Choose up to 3 to compare

The check mark shows an option that has figures verified against a cited source.

EPS (expanded polystyrene)

Standard: Product-specific

Relative cost: Lower

Specifications

  • Approx. thermal conductivity

    0.036-0.040 W/mK

    Derived- Studio Matrx(derived from R 3.6-4.0 per inch)

  • Moisture

    Good

    Verified- Studio Matrx

  • Fire

    Organic foam - burns; needs fire-rated facing or barrier

    Verified- Studio Matrx

Advantages

  • Economical
  • Light

Disadvantages

  • Combustible
  • Needs protection

Best for

Roof and wall insulation with fire-safe detailing.

Avoid

Exposed use.

XPS (extruded polystyrene)

Standard: Product-specific

Relative cost: Medium

Specifications

  • Approx. thermal conductivity

    0.029-0.032 W/mK

    Derived- Studio Matrx(derived from R 4.5-5.0 per inch)

  • Moisture

    Excellent (closed cell)

    Verified- Studio Matrx

  • Fire

    Organic foam - burns; needs fire-rated facing or barrier

    Verified- Studio Matrx

Advantages

  • Closed-cell, moisture resistant
  • Higher R per inch than EPS

Disadvantages

  • Combustible
  • Higher cost than EPS

Best for

Inverted roofs and damp-prone areas.

Avoid

Unprotected exposure to flame or sun.

PU / PIR foam

Standard: Product-specific

Relative cost: Higher

Specifications

  • Approx. thermal conductivity

    0.022-0.026 W/mK

    Derived- Studio Matrx(derived from R 5.5-6.5 per inch)

  • Moisture

    Excellent (closed cell)

    Verified- Studio Matrx

  • Fire

    Combustible; PIR chars rather than melts

    Verified- Studio Matrx

Advantages

  • Best insulation per thickness here
  • Closed-cell

Disadvantages

  • Highest cost
  • Needs facing and fire detailing

Best for

Where thickness is limited.

Avoid

Ignoring fire detailing.

Common mistakes

  • Leaving gaps or crushed insulation that cuts performance.
  • Using foam near heat or electrics without checking fire rating.
  • Insulating without a moisture strategy.

Ask the shop

  • What is the thermal conductivity and density?
  • What fire rating does the product carry?
  • How is it fixed and protected?

Words you will hear

R-value / U-value
Resistance to or transfer of heat through a layer.
Density
Weight per volume; affects strength.
Thermal bridge
A path where heat bypasses the insulation.

Next steps

How to choose

  • Compare R-value at the thickness you can actually fit.
  • Check fire rating and whether a protective facing is required.
  • Keep fibrous insulation dry.
  • Place roof insulation to suit the waterproofing layout.

Sources and how far to trust them

Limits of this comparison: k values are DERIVED by us from a reference site's R-per-inch figures (k = 0.1442 / R-per-inch). They are indicative only. IS 3346 covers thermal conductivity testing; ECBC sets envelope limits.

Standards are revised. Confirm any value you rely on against the current edition on the BIS website. Information is for planning, not a specification.

More envelope comparisons