Skip to content
SPSDPSPlanning & Building Tools

Plumbing pipes: CPVC, uPVC, PPR and GI

The first question is temperature: which pipe is rated for hot water. Only CPVC ratings were verified against a BIS standard here; the other pipes are covered by guidance and you should read their own BIS standards.

Cost tiers are RELATIVE only (lower / medium / higher). SPSDPS does not publish current prices - get written local quotations.

The short answer

Use the right pipe for the job (hot, cold, drain) and a licensed plumber who tests before closing walls.

If your situation is this, choose that
If you need...ConsiderWhy
Hot and cold water inside the houseCPVC or PPRBoth designed for hot water; follow maker's jointing method.
Drainage and soil linesuPVC drainage pipeRight pipe for gravity drains.
Cold pressurised linesuPVC pressure pipe or PPRCheck the pressure rating.
Old repairs on existing GI linesPlan replacementGI corrodes over time.

All options at a glance

All options at a glance
OptionRelative costBest forWatch out for
CPVCMedium to higherHot and cold water supply lines in homes.Pressure rating drops sharply at high temperature
uPVC (pressure and drainage)LowerCold water supply and drainage as rated.Not intended for hot water
PPRMediumConcealed hot and cold lines.Needs a fusion tool and trained installer
GI (galvanised iron)MediumExposed risers and where metal is required.Corrodes over time with some water chemistries

Compare side by side

Choose up to 3 to compare

The check mark shows an option that has figures verified against a cited source.

CPVC

Standard: IS 15778:2007

Relative cost: Medium to higher

Specifications

  • Intended use

    Potable hot and cold water distribution; water service up to and including 82 C

    Verified- Bureau of Indian Standards

  • Working pressure, Class 1 (SDR 11)

    2.76 MPa at 27 C; 0.68 MPa at 82 C

    Verified- Bureau of Indian Standards

  • Working pressure, Class 2 (SDR 13.5)

    2.18 MPa at 27 C; 0.55 MPa at 82 C

    Verified- Bureau of Indian Standards

  • Working pressure, Class 3 (SDR 17)

    1.73 MPa at 27 C; 0.42 MPa at 82 C

    Verified- Bureau of Indian Standards

  • Nominal sizes

    DN 15 to DN 150

    Verified- Bureau of Indian Standards

Advantages

  • Designed for hot and cold potable water
  • Solvent-cement joints are quick

Disadvantages

  • Pressure rating drops sharply at high temperature
  • Needs correct solvent cement and curing

Best for

Hot and cold water supply lines in homes.

Avoid

Mixing solvent cements or fittings from different systems.

uPVC (pressure and drainage)

Standard: Check applicable IS for use

Relative cost: Lower

Specifications

No standard values quoted. Compare using the product data sheet and a batch test report.

Advantages

  • Economical
  • Light and easy to install

Disadvantages

  • Not intended for hot water
  • UV degrades exposed pipe

Best for

Cold water supply and drainage as rated.

Avoid

Hot water lines.

PPR

Standard: Check applicable IS for use

Relative cost: Medium

Specifications

No standard values quoted. Compare using the product data sheet and a batch test report.

Advantages

  • Heat-fusion joints are leak-free when done right
  • Suited to hot and cold lines as rated

Disadvantages

  • Needs a fusion tool and trained installer
  • Expansion needs allowance on long runs

Best for

Concealed hot and cold lines.

Avoid

Untrained installers.

Common mistakes

  • Using cold-water pipe for hot water.
  • Closing walls before a pressure test.
  • Mixing fittings from different makers without checking compatibility.

Ask the shop

  • What is the pressure and temperature rating?
  • Which jointing method (solvent, fusion) is needed?
  • Which fittings are included?

Words you will hear

Pressure test
Holding the line under water pressure to find leaks.
Fusion welding
Heat joining used for PPR.
Trap
Water seal in a drain that stops odours.

Next steps

How to choose

  • Separate hot and cold lines by rated temperature.
  • Use fittings from the same system and approved solvent/fusion method.
  • Pressure-test the lines before closing walls.
  • Ask for the BIS mark and pipe class on the pipe marking.

Sources and how far to trust them

Limits of this comparison: CPVC data is from an OCR scan of IS 15778:2007 (later amended). Check the current edition. uPVC, PPR and GI properties are general guidance only.

Standards are revised. Confirm any value you rely on against the current edition on the BIS website. Information is for planning, not a specification.

More services comparisons