Skip to content
SPSDPSPlanning & Building Tools

Walling units: bricks and blocks

The wall unit decides weight, thermal comfort, mortar use and how fast a wall goes up. Figures marked Verified come from the cited standard; everything else is general guidance.

Cost tiers are RELATIVE only (lower / medium / higher). SPSDPS does not publish current prices - get written local quotations.

The short answer

The wall unit sets weight, insulation, speed of work and plaster cost. Pick by structure type first, price second.

If your situation is this, choose that
If you need...ConsiderWhy
You want lighter walls and faster constructionAAC blocksLower weight reduces load on the structure; large blocks lay quickly. Needs the right mortar and plaster system.
You want the traditional, easily available optionBurnt clay brickFamiliar to every mason. Quality varies, so check strength and uniformity.
You need a load-bearing or boundary wallSolid concrete block or good-quality brickAsk the structural engineer; do not use light blocks where strength is required.
You want to reduce clay useFly-ash brickUses industrial by-product; check the grade and supplier test report.

All options at a glance

All options at a glance
OptionRelative costBest forWatch out for
Common burnt clay brickLowerLoad-bearing and boundary walls where a suitable class is specified.Heavy
Autoclaved aerated concrete (AAC) blockMediumFramed-structure infill walls and partitions.Needs the supplier's recommended jointing and plaster system
Solid / hollow concrete blockMediumCompound walls, retaining and load-bearing walls as designed.Heavy
Fly-ash brickLower to mediumGeneral masonry where a tested, classified product is supplied.Quality varies between producers

Compare side by side

Choose up to 3 to compare

The check mark shows an option that has figures verified against a cited source.

Common burnt clay brick

Standard: IS 1077:1992

Relative cost: Lower

Specifications

  • Compressive strength classes

    3.5, 5, 7.5, 10, 12.5, 15, 17.5, 20, 25, 30, 35 N/mm2 (minimum average)

    Verified- Bureau of Indian Standards

  • Water absorption (24 h cold immersion)

    Max 20% by weight up to class 12.5; max 15% for higher classes

    Verified- Bureau of Indian Standards

  • Efflorescence

    Not more than "moderate" up to class 12.5; "slight" for higher classes

    Verified- Bureau of Indian Standards

  • Modular size

    190 x 90 x 90 mm (also 190 x 90 x 40 mm)

    Verified- Bureau of Indian Standards

  • Non-modular size

    230 x 110 x 70 mm (also 230 x 110 x 30 mm)

    Verified- Bureau of Indian Standards

Advantages

  • Familiar to every mason
  • Good thermal mass
  • Easy to cut, fix and repair

Disadvantages

  • Heavy
  • Quality varies by kiln and batch
  • More joints than large blocks

Best for

Load-bearing and boundary walls where a suitable class is specified.

Avoid

Unclassified or visibly over-burnt / soft bricks.

Autoclaved aerated concrete (AAC) block

Standard: IS 2185 (Part 3) - draft revision

Relative cost: Medium

Specifications

  • Oven-dry density covered

    451 to 1000 kg/m3

    Verified- Bureau of Indian Standards

  • Minimum compressive strength (Grade 1 / Grade 2)

    551-650 kg/m3: 4.0 / 3.0 N/mm2; 651-750: 5.0 / 4.0 N/mm2

    Verified- Bureau of Indian Standards

  • Max thermal conductivity (air-dry)

    0.21 W/mK at 451-550 kg/m3 up to 0.42 W/mK at 851-1000 kg/m3

    Verified- Bureau of Indian Standards

  • Drying shrinkage limit

    0.05% (Grade 1), 0.10% (Grade 2)

    Verified- Bureau of Indian Standards

  • Nominal length / height / width options

    L 400, 500, 600, 625 mm; H 200, 100 mm; W 50-300 mm

    Verified- Bureau of Indian Standards

Advantages

  • Light, so less dead load
  • Large units mean fewer joints
  • Lower thermal conductivity than clay or solid concrete

Disadvantages

  • Needs the supplier's recommended jointing and plaster system
  • Heavy fixings need proper anchors
  • Must be protected from prolonged wetting

Best for

Framed-structure infill walls and partitions.

Avoid

Below-ground or constantly wet locations unless protected as the manufacturer specifies.

Solid / hollow concrete block

Standard: IS 2185 (Part 1)

Relative cost: Medium

Specifications

No standard values quoted. Compare using the product data sheet and a batch test report.

Advantages

  • Consistent size
  • Fast to build
  • Available in many thicknesses

Disadvantages

  • Heavy
  • Hollow blocks need cores handled correctly
  • Higher thermal conductivity than AAC

Best for

Compound walls, retaining and load-bearing walls as designed.

Avoid

Using hollow blocks for loads they are not rated for.

Common mistakes

  • Using ordinary cement-sand mortar and thick plaster on AAC instead of the maker's recommended jointing and plaster system.
  • Mixing different unit types in one wall without joint reinforcement or expert advice.
  • Skipping a sample test of strength and water absorption for a large order.

Ask the shop

  • Which standard does this unit comply with?
  • Can I see a recent test report for compressive strength?
  • What mortar or adhesive do you recommend with it?

Words you will hear

Compressive strength
How much load a unit carries before crushing.
Load-bearing wall
A wall that carries floors or roofs above it.
Infill wall
A wall that only separates rooms inside a framed structure.

Next steps

How to choose

  • Check the load path first: whether the wall is load-bearing or infill is a structural engineer's decision.
  • Ask the supplier for a test report for the exact batch (compressive strength, water absorption).
  • Match the mortar or adhesive system to the unit - AAC and clay do not use the same joint practice.
  • Protect every unit from rain on site; wet units behave differently when plastered.

Sources and how far to trust them

Limits of this comparison: The AAC figures come from a BIS DRAFT, not the final standard. Concrete-block and fly-ash brick limits were not verified for this build - take them from the current IS 2185 (Part 1) and the applicable fly-ash brick standard.

Standards are revised. Confirm any value you rely on against the current edition on the BIS website. Information is for planning, not a specification.

More structure comparisons