Skip to content
SPSDPSPlanning & Building Tools

Tile adhesive and grout compared

The adhesive and grout hold your tiles for years. Large or dense tiles and wet areas need better adhesive than old-style cement-sand mortar.

Cost tiers are RELATIVE only (lower / medium / higher). SPSDPS does not publish current prices - get written local quotations.

The short answer

Use polymer-modified adhesive for most tile jobs; use epoxy only where wet, stain-prone or chemical exposure demands it.

If your situation is this, choose that
If you need...ConsiderWhy
Large or dense tilesPolymer-modified adhesiveBetter bond than plain cement mortar.
Kitchen or wet roomEpoxy grout (or good adhesive and sealed grout)Stain and water resistant.
Thick levelling bed under floor tilesCement-sand bedFor levelling, with correct adhesive on top if required.

All options at a glance

All options at a glance
OptionRelative costBest forWatch out for
Cement-sand bedLowerThick bed under standard floor tiles.Weak bond with dense tiles
Polymer-modified cement adhesiveMediumMost floor and wall tile jobs.Needs flat surface
Epoxy adhesive and groutHigherKitchens, wet rooms and chemical-prone areas.Costly and harder to work with
Cement-based groutLower to mediumOrdinary dry floors and walls.Can stain and need sealing

Compare side by side

Choose up to 3 to compare

The check mark shows an option that has figures verified against a cited source.

Cement-sand bed

Standard: Product-specific

Relative cost: Lower

Specifications

No standard values quoted. Compare using the product data sheet and a batch test report.

Advantages

  • Cheap and familiar
  • Good for levelling thick beds

Disadvantages

  • Weak bond with dense tiles
  • Needs soaking and skill

Best for

Thick bed under standard floor tiles.

Avoid

Large or low-absorption tiles and wall tiles.

Polymer-modified cement adhesive

Standard: Product-specific

Relative cost: Medium

Specifications

No standard values quoted. Compare using the product data sheet and a batch test report.

Advantages

  • Strong bond
  • Thin bed
  • Suits large tiles

Disadvantages

  • Needs flat surface
  • Open time is limited

Best for

Most floor and wall tile jobs.

Avoid

Using it far beyond its open time.

Epoxy adhesive and grout

Standard: Product-specific

Relative cost: Higher

Specifications

No standard values quoted. Compare using the product data sheet and a batch test report.

Advantages

  • Very strong and stain-resistant
  • Waterproof

Disadvantages

  • Costly and harder to work with
  • Short working time

Best for

Kitchens, wet rooms and chemical-prone areas.

Avoid

DIY use without trial.

Common mistakes

  • Using cement slurry with dense tiles.
  • Skipping the notched trowel and leaving gaps below tiles.
  • Grouting before the adhesive has cured.

Ask the shop

  • Which tile sizes and types is this adhesive for?
  • What is the open time and coverage?
  • What grout widths does this grout suit?

Words you will hear

Open time
How long the adhesive stays workable.
Notched trowel
Trowel that leaves ridges of adhesive.
Hollow tile
A tile with an air gap below, a common failure.

Next steps

How to choose

  • Match the adhesive to tile size, water absorption and surface.
  • Large-format and low-absorption tiles generally need polymer-modified adhesive.
  • Use the notched trowel size on the adhesive pack.
  • Choose grout by joint width and exposure to water and stains.

Sources and how far to trust them

Limits of this comparison: Qualitative guidance only. No strength, thickness, rating or price figures are quoted because they vary by product. Check each maker's data sheet.

This category uses general professional guidance, not quoted standard values. Read the product data sheet and ask for test reports.

Standards are revised. Confirm any value you rely on against the current edition on the BIS website. Information is for planning, not a specification.

More finishes comparisons